When the sun goes down, your solar fairy lights will automatically turn on and provide up to 8 hours of light. To make your own solar fairy lights, you will need: solar string lights, a Mason jar with a lid, scissors, and clear packing tape. Start by screwing the Mason jar lid onto the bottom of the solar panel.

Then, cut a small hole in the center of the lid. Next, thread the string of lights through the hole in the lid and into the Mason jar. Finally, seal up the hole with clear packing tape.

These charming DIY solar fairy lights are perfect for adding a touch of magic to any outdoor space!

  • Cut a hole in the bottom of each plastic cup
  • string the lights through the holes in the cups
  • Hang the fairy lights in a sunny spot
  • Enjoy your solar powered fairy lights!

Can I Make My Own Solar Light?

You can make your own solar lights using a few different methods. The most common is to use a mason jar and some wire. You will need to drill a hole in the lid of the jar, and then thread the wire through it.

Attach a small solar panel to the end of the wire, and then place the panel in direct sunlight. The solar panel will collect energy from the sun and convert it into electricity, which will then power the LED light inside the jar.

How Do You Make a Simple Solar Light?

If you’re looking for a quick and easy solar light, here’s how to make one with just a few supplies. You’ll need: -A Mason jar with lid

-A small solar panel (we used a 1.5V 100mA panel) -An LED light (we used a white LED) -Wiring (we used 22 gauge solid core wire)

-A drill -Super glue or hot glue Optional:

Paint or decoration for your jar Instructions: 1. Drill a hole in the center of the mason jar lid.

The size of the hole will depend on the size of your solar panel’s wires. Ours were about 2mm in diameter, so we drilled a 3/32″ hole. 2. Feed the wires from the solar panel through the hole in the lid and screw the lid onto the jar snugly.

If needed, use superglue or hot glue around the edges of the lid to create a seal. This will keep water out when it rains. 3. Once the lid is securely fastened, connect your LED light to the positive and negative leads from your solar panel using your wiring.

We soldered our connections, but you can also use twist ties or tape if you don’t have access to soldering equipment. Make sure that your connections are secure so that moisture doesn’t get in and cause problems later on down the road.

What Voltage are Solar Fairy Lights?

Most solar fairy lights use a 3.7 volt battery. Some of the higher end models use a 6 volt battery, but this is not as common. The voltage of the battery will determine how bright the lights are.

A higher voltage means brighter lights.

How Do You Make Solar Fairy Lights Last Longer?

When it comes to solar fairy lights, there are a few things you can do to make them last longer. First, be sure to charge the batteries fully before use. This will help ensure that the lights have enough power to run for an extended period of time.

Additionally, avoid leaving the lights on for extended periods of time as this can drain the battery more quickly. Finally, be sure to clean the solar panel regularly so that it can continue to efficiently collect energy from the sun. By following these simple tips, you can help your solar fairy lights last longer and continue to provide beautiful illumination in your home or garden.

DIY Solar Fairy Light Jar

Convert Plug in Lights to Solar

Are you tired of your energy bills going up every month, even though you’re doing everything you can to be more energy efficient? If so, you may want to consider converting your plug-in lights to solar. Solar lights are a great way to save money on your energy bill, and they’re also much better for the environment than traditional electric lights.

Here’s a quick guide to help you convert your plug-in lights to solar: 1. Start by purchasing some solar lights. You can find these at most home improvement stores or online.

2. Once you have your solar lights, carefully remove the light bulb from each fixture. Be careful not to break the bulbs! 3. Next, use a screwdriver to remove the screws that hold the fixture in place.

Again, be careful not to damage anything as you work. 4. With the screws removed, gently pull the fixture away from the wall or ceiling. If it’s difficult to remove, check for any additional fasteners that may be holding it in place (such as nails).

5. Now take your new solar light and hold it up against the hole left by the old fixture. Use a pencil or marker to trace around the outer edge of the light onto the wall or ceiling surface. This will give you an easy template to follow when installing your new light.

6 . Carefully cut out the tracing with a utility knife or other sharp tool – being sure not to damage any wires that may be behind the wall/ceiling surface .Create a hole just big enough for the base of the new light to fit snugly into .


Looking for a unique way to light up your yard or garden? Check out these solar fairy lights! They are easy to make and require no electricity.

All you need is some wire, solar cells, batteries, and LED lights. You can find all of these materials at your local hardware store. To start, cut the wire to the desired length.

Next, strip the insulation off of the end of the wire and attach the solar cell. Then, do the same with the other end of the wire and attach the LED light. Finally, connect the battery and turn on the switch!

The solar cell will charge the battery during daytime hours, and then the LED will automatically turn on at night.

Leave a Reply

Your email address will not be published. Required fields are marked *